- 1 K40 laser water cooling
- 2 K40 laser exhaust
- 3 K40 laser power supply
- 4 K40 laser optics and mirrors
- 5 Bed´s and jigs for the K40 laser machine
- 6 K40 laser controller boards
- 7 K40 laser lights
- 8 Your K40 machine suggestions
The K40 laser machine is a awesome little product who makes it easy for hobby and semi-pro use to get going with laser cutting or engraving.
It´s far from perfect and needs a hand to work as you intended.
First reading should be the article about checking your machine – K40 electrical warnings – first setup.
K40 laser water cooling
Depending on where you live, it might be a good option to have a bigger tank 15-25L or more.
If you live in a hot climate, you need a bigger tank to keep the coolant colder for longer, a small tank will heat up quicker. Check out cooling upgrades below.
The included pump coming with the machine is good enough and will work as intended. Make sure the pump is at the bottom of the tank and return-hose below water level.
Optimum coolant temperature is below 22 celsius.
Anything above will slow down the regeneration-process inside the laser tube, where the gasses are recombined to new Co2. If this process slows down you are using more “power” out of the tube than it regenerates and you will get a tube dying on you prematurely.
Read more about coolant types here
This part could be a own article. But i keep it simple for this article.
I would point at three types of cooling upgrades.
1: Radiator in the water loop, to cool the water with ambient temperatures.
2: Peltier cooler, very inefficient but does the job – to a certain limit
3: Gas powered coolers, dedicated coolers like CW5000 or DIY built from a refrigerator.
K40 laser exhaust
Sealing the machine
Smell from the machine is both annoying and might be dangerous depending on what you cut.
Sealing the machine will help keeping the gasses inside the case and out the exhaust, this can be done with duct tape, hot glue or silicone to seal the openings and cracks in the machine.
Change the exhaust fan
The included fan is both dangerous and bad, it will partially do the work but there is much to do.
Read this bigger article about exhaust fans.
K40 laser power supply
All electronic products have problems with heat, the more heat the lower the efficiency. Our K40 lasers has the same problems.
To prolong your life on the PSU you can do a few fixes to help this out.
1: Add ventilation to the small compartment where the PSU is located.
2: Tilt your PSU, to draw ambient temp in to the fan on top. Tilt your K40 laser power supply.
Add extra PSU
Relieving the power supply from extra load is a approach you should have in mind every time adding anything to the machine.
Never add lights or peripherals directly to the laser power supply. Install a extra PSU for all your needs. A old computer PSU will work fine!
If you want, you can install a extra 24V PSU to run your controller board, taking even more load away from the laser power supply and minimizing the risk of anything going wrong.
A power supply with 5V, 12V and 24V can be bought from Ebay, aliexpress and amazon for 30-50 USD.
K40 laser optics and mirrors
Change lens and mirrors
When delivered, most of the machines has the cheapest availible mirrors and lens installed.
Changing this up will gain you a lot. Both in cutting power and less power needed for cutting.
Mirrors needed: 20mm MO or SI mirrors
Lens needed: 12mm ZnSE, GAAS or GE mirror.
Read more about mirrors and lenses here
Cleaning your optics are very important. When the mirrors get dirty the tend to allocate the energy and get hot. If your mirrors gets hot it is a sign that your mirrors are dirty.
Read more about cleaning your K40 laser lens and mirrors here
Add a fan to the laser head
The air assist saga is a controversial one, i have written more detailed article about it Air assist on K40 laser machines
The basic function is to keep the cut clear from smoke and debris to help out the beam evaporate the material when cutting or engraving.
Bed´s and jigs for the K40 laser machine
Change your bed
When the machine arrives, it´s often installed with a metal bed and a big clamp.
The optimal focus for these machines are 50.8mm focal point.
With the original bed, anything you put on top of the bed is out of focus, it´s actually inside the clamp. To use the full width of the machine you need to change your bed.
Read more about upgrading your bed here
Why sax-lift tables are (often) bad
There is cheap lifts on ebay, aliexpress and similar you can buy that are attractive to use.
Beware of this type of movable bed, they are often not tight in the joints making the bed wobble in all direction. As the focal point is very important you cannot have a bed shifting up-down with 2-5mm when you put anything on it.
There is more premium ones that will work good, or you can DIY fix your cheap-o lift to tighten it up in the joints.
Jigs and edges
Jigs and edges will help your out aligning material, parts or products for cutting and/or engraving if you do a lot of series.
A jig may be a piece you fit inside the machine with holes, and then drop in your 20 pencils inside these holes and opening your template changing the text to engrave.
This is also good when doing double-sided engravings to get the engraving aligned on the piece.
Read more here how to create your own jigs and templates
K40 laser controller boards
There is different solutions for the machines, with better control and handling and bigger options for settings and software to use with your K40.
Here i list the most common upgrades.
This is a prepared kit to convert your K40 for use with LaserWeb4 and other Gcode-compatible softwares.
This is by far the easiest upgrade with very similar results as the other ones. Seen to the price it´s #2
More details here: http://cohesion3d.com/
Lightobject DSP kit
This is a prepared kit to convert your K40 for use with a AWC DSP controller..
More details here: http://www.lightobject.com/X7-DSP-upgrade-kit-for-DK40-small-CO2-laser-machine-P942.aspx
Ramps 1.4 kit
This is actually a 3D-printer kit, but there is different firmwares focused on the K40 upgrade.
I am still upgrading one of my machines, so i´ll add more information later.
More details here: https://github.com/ExplodingLemur/presentations/wiki/K40-RAMPS-Conversion
The Smoothieboard is similar to Cohesion3D (smoothiebased).
Read more about it here: http://smoothieware.org/laser-cutter-guide
K40 laser lights
Adding more lights to your machine is always a nice upgrade. More visibility and it looks good too.
Use a external power supply and add LED-strips inside your machine of your liking.
Adding them into the lid or under the Y-carriage will help a bit with blinding you when using the machine.
Your K40 machine suggestions
Do you have a upgrade, update or mod you want to share? Comment below!